NOTICE DATE: October 1,
2010
NOTICE TYPE: R-C10012010-01
Informational: TX SET Change Controls
SHORT DESCRIPTION: TX SET
Change Controls for TX SET 4.0
INTENDED AUDIENCE: CRs and
TDSPs
LONG DESCRIPTION: The Texas
Standard Electronic Transaction (TX SET) Working Group is currently gathering
requirements for a release of TX SET version 4.0 and will be accepting all new
change controls through October 29, 2010.
A copy of the Change Control Form can be found under the Key Documents on
the Texas Standard Electronic Transaction Guides pages at: http://www.ercot.com/mktrules/guides/txset/.
Please submit any new Change Controls to [log in to unmask]
for changes to be added to the next TX SET release.
A TX SET Change Control Conference
Call will occur on Tuesday, October 12, 2010 at 1:00 pm. The following
Change Controls will be discussed:
New Change Controls to be discussed:
ChangeControl2008-726: Revised PUCT Subs. Rule 25.181 allows for the breakout of the
Energy Efficiency Cost Recovery Factor (EECRF) from TDSPs base rates. (To be included in 3.0A)
ChangeControl2010-733:
Discontinue use of the following transactions
submitted to ERCOT by a CR: 814_07, 814_09, 814_13, 814_15, 814_19, 814_21,
814_23 & 814_29.
ChangeControl2010-734:
In order to support the Meter Tampering
Rulemaking a new REF segment should be added to the 814_20 to communicate
Switch Hold Add and Removal. In addition, a new Reason for Change should be
added to REF~TD to communicate change in Switch Hold Status.
ChangeControl2010-735:
In order to support Meter Tampering, in the
event of a Mass Transition, the POLR CR will be notified that an ESI ID had a
Switch Hold prior to the Mass Transition in a new REF segment.
ChangeControl2010-736:
In order to reject a Move In or Switch which
currently has a Switch Hold, a new reject code of SHF will be added to the
appropriate transactions.
ChangeControl2010-737:
In order to support the Meter Tampering
Rulemaking, changes were added to the 650_01 and 650_02 to communicate Switch
Hold Disconnect and Reconnect.
ChangeControl2010-738:
New Critical Care status designations are
required when Critical Care = Y and additional contact information is required
for certain Critical Care statuses.
ChangeControl2010-739:
Changes are required to the 814_PC in order
for the TDSPs to receive customer contact information for power outages and
service restoration.
ChangeControl2010-740:
If the 814_27 is received with the REF~1P~HUU
(Status Reason) HISTORICAL USAGE UNAVAILABLE, both ERCOT and the requesting CR
should close the Business Process Instance (BPI) and the 867_02 transaction
should not be expected by the CR or ERCOT.
ChangeControl2010-741:
Adding a priority code to the 814_24 to allow
for same day requests to be processed at a different level from standard Move
Outs.
ChangeControl2010-742:
Addition of a new reject code ACR –
Acquisition Cancel Reject to be used when a CR submits an 814_08 on an
Acquisition.
ChangeControl2010-743:
Addition of a new reject code CW1 for use when
a CR submits an 814_08 or 814_12 within 1 Retail Business Day of a Scheduled
Meter Read Date.
ChangeControl2010-745:
Add the ability for a TDSP to Complete
Unexecutable a Switch.
ChangeControl2010-746:
TX SET Guide changes by transaction required
to support Acquisition Transfer.
ChangeControl2010-747:
In order to provide REPs information on
whether an ESI ID has a provisioned Advanced Meter installed at the premise, a
new REF segment will be added to the 814_04, 814_05, 814_22 and 814_20.
ChangeControl2010-748:
The purpose of this Change Control is to sync
the names of the Texas SET Guide transactions, with the names of the
transaction in Protocol and the Retail Market Guide.
ChangeControl2010-749:
The 810_03 Implementation Guide should be
updated to show that for LPC001 – Late Payment, remove the requirement
for an Invoice Number (REF~1K segment required when SAC04 = LPC001).
ChangeControl2010-750:
The addition of new SAC04 codes to the 810_02
transaction
ChangeControl2010-751:
Addition of two new reject codes FME (Force
Majeure Event) and WTM (Weather Moratorium) to multiple transactions.
ChangeControl2010-752:
Removal of an incorrect link in multiple
Implementation Guides on the location of the ISO Country Codes.
Under Review Change Controls to be
discussed:
ChangeControl2008-722: The 650_04 Implementation Guide currently requires Originating Tran ID
and Estimated Restoration Date whenever purpose code = ‘79’.
It is actually only required when purpose code = 79 AND Suspension/Reactivation
code = RC001. This causes false rejection of 650_04 Reactivate after disconnect
for denial of access when Origination Transaction ID and Estimated Restoration
Date is not also included.
ChangeControl2008-723:
Need to add four (4) new SAC04 codes to the
Muni/Coop 810_03 INV. (To be included in
3.0A)
ADDITIONAL INFORMATION: This meeting will be held on October 12, 2010 from
13:00 to 17:00 at the ERCOT MET Center, 7620 Metro Center Drive, Austin, Texas
78744 in conference room 206B.
Those wishing to attend via Web Ex
or conference call may do so by following the instructions below.
Meeting information
Topic: TX
SET Change Control
Date:
Tuesday, October 12, 2010
Time: 1:00 PM, Central Daylight Time
Audio
conference information
Call-in
toll-free number (US/Canada): 1-866-469-3239
To join the online meeting, go to:
https://ercot.webex.com/ercot/j.php?ED=140405412&UID=482806862&PW=NNDE4MjJiNzAx&RT=MiM3
Meeting Password: Txsetcc123!!
Meeting Number: 352 090 086
CONTACT:
If you have any questions, please contact your ERCOT Account Manager.
You may also call the general ERCOT Client Services phone number at (512)
248-3900 or contact ERCOT Client Services via e-mail at [log in to unmask].
If you are
receiving e-mail from an ERCOT distribution list that you no longer wish to
receive, please follow this link in order to unsubscribe from this list: http://lists.ercot.com.
JR/DH